The mass flow distribution and local flow structures that lead to areas of reactant starvation are explored for a small power large active area PEM fuel cell. A numerical model was created to examine the flow distribution for three different inlet profiles; blunt, partially developed, and fully developed. The different inlet profiles represent the various distances between the blower and the inlet to the fuel cell and the state of flow development. The partially and fully developed inlet profiles were found to have the largest percentage of cells that are deficient, 20% at a flow rate of 6.05 g/s. Three different inlet mass flow rates (stoichs) were also examined for each inlet profile. The largest percent of cells deficient in reactants is 27% and occurs at the highest flow rate of 9.1 g/s (3 stoichs) for the partially and fully developed turbulent profiles. In addition to the uneven flow distribution, flow separation occurs in the front four channels for the blunt inlet profile at all flow rates examined. These areas of flow separation lead to localized reactant deficient areas within a channel.
Skip Nav Destination
Article navigation
February 2006
This article was originally published in
Journal of Fuel Cell Science and Technology
Research Papers
Effects of Inlet Mass Flow Distribution and Magnitude on Reactant Distribution for PEM Fuel Cells
M. McGarry,
M. McGarry
The College of New Jersey
, Ewing, New Jersey 08628-0718
Search for other works by this author on:
L. Grega
L. Grega
The College of New Jersey
, Ewing, New Jersey 08628-0718
Search for other works by this author on:
M. McGarry
The College of New Jersey
, Ewing, New Jersey 08628-0718
L. Grega
The College of New Jersey
, Ewing, New Jersey 08628-0718J. Fuel Cell Sci. Technol. Feb 2006, 3(1): 45-50 (6 pages)
Published Online: July 20, 2005
Article history
Received:
March 21, 2005
Revised:
July 20, 2005
Citation
McGarry, M., and Grega, L. (July 20, 2005). "Effects of Inlet Mass Flow Distribution and Magnitude on Reactant Distribution for PEM Fuel Cells." ASME. J. Fuel Cell Sci. Technol. February 2006; 3(1): 45–50. https://doi.org/10.1115/1.2134736
Download citation file:
Get Email Alerts
Cited By
Optimization of thermal non-uniformity challenges in liquid-cooled lithium-ion battery packs using NSGA-II
J. Electrochem. En. Conv. Stor
Ultrasound-enabled adaptive protocol for fast charging of lithium-ion batteries
J. Electrochem. En. Conv. Stor
Effects of Sintering Temperature on the Electrical Performance of Ce0.8Sm0.2O1.9–Pr2NiO4 Composite Electrolyte for SOFCs
J. Electrochem. En. Conv. Stor (August 2025)
Joint Model Parameter Identification and EKF Algorithm for the SOC Estimation of LFP Battery
J. Electrochem. En. Conv. Stor
Related Articles
Modeling of a Proton Exchange Membrane Fuel Cell With a Large Active Area for Thermal Behavior Analysis
J. Fuel Cell Sci. Technol (November,2008)
Simplified Model to Predict Incipient Flooding/Dehydration in Proton Exchange Membrane Fuel Cells
J. Fuel Cell Sci. Technol (August,2007)
Orientation-Dependent Performance of Portable Proton Exchange Membrane Fuel Cells
J. Fuel Cell Sci. Technol (June,2011)
Experimental Study of the Local Convection Heat Transfer From a Wall-Mounted Cube in Turbulent Channel Flow
J. Heat Transfer (August,1999)
Related Proceedings Papers
Related Chapters
Experiment Study on the Current Density Distribution of PEMFC
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)
Three-Dimensional Numerical Simulation and Design of PEM Fuel Cell
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)
Low-Cost and Light Bipolar Plates of PEM Fuel Cell
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)