A promising type of proton exchange membrane fuel cell (PEMFC) architecture, the ribbon fuel cell, relies on the gas diffusion layer (GDL) to conduct electrical current in-plane to adjacent cells or collector terminals. The potential advantages of the fuel cell ribbon architecture with respect to conventional fuel cell stacks include reduced manufacturing costs, reduced weight, reduced volume, and reduced component cost. This work addresses the critical component of fuel cell ribbon assemblies, which is the GDL. The materials and treatments necessary to fabricate GDLs for fuel cell ribbon assemblies are presented along with experimental results for various candidate gas diffusion materials. An experimentally validated analytical model, which focuses on the electrical losses within the GDL of the ribbon fuel cell, was developed and used to guide design and testing. Low in-plane resistance is extremely important for the ribbon architecture because high in-plane GDL resistance can cause significant variation in current density over the catalyzed area. To reduce the current variation the new GDLs are fabricated with materials that have reduced in-plane resistance. Properties and performance for a common gas diffusion media, ELAT® LT-1200W (BASF Fuel Cell), were measured as a reference for the new gas diffusion layers. The widely used ELAT material exhibited an in-plane resistance of , whereas the new diffusion materials exhibited in-plane resistances in the range of . The performance of a ribbon fuel cell was predicted using a two-dimensional model that combines the polarization curve for a conventional bipolar plate type PEMFC and the resistive properties of the GDL material of interest. Experiments were performed to validate the analytical model and to prove the feasibility of the ribbon fuel cell concept. Results show that when the novel GDLs were adhered to a catalyzed membrane and tested in a ribbon fuel cell test assembly utilizing serpentine flow channels and in-plane current collection, a range of performance was achieved between and at a cell potential of 0.5 V. The agreement between the experimental data and the model predictions was very good for the ELAT and the B1/B polyacrylonitrile (PAN)-based carbon cloth. Differences between predicted and measured performance for a pitch-based GDL material were more significant and likely due to mass transport limitations.
Skip Nav Destination
e-mail: jsole@vt.edu
e-mail: mwellis@vt.edu
e-mail: dillard@vt.edu
Article navigation
November 2009
This article was originally published in
Journal of Fuel Cell Science and Technology
Research Papers
Experimental and Analytical Study of Gas Diffusion Layer Materials for Ribbon Fuel Cells
J. D. Sole,
J. D. Sole
Department of Electrical Engineering,
e-mail: jsole@vt.edu
Virginia Polytechnic Institute and State University
, Blacksburg, VA 24061
Search for other works by this author on:
M. W. Ellis,
M. W. Ellis
Department of Electrical Engineering,
e-mail: mwellis@vt.edu
Virginia Polytechnic Institute and State University
, Blacksburg, VA 24061
Search for other works by this author on:
D. A. Dillard
D. A. Dillard
Department of Engineering Science and Mechanics,
e-mail: dillard@vt.edu
Virginia Polytechnic Institute and State University
, Blacksburg, VA 24061
Search for other works by this author on:
J. D. Sole
Department of Electrical Engineering,
Virginia Polytechnic Institute and State University
, Blacksburg, VA 24061e-mail: jsole@vt.edu
M. W. Ellis
Department of Electrical Engineering,
Virginia Polytechnic Institute and State University
, Blacksburg, VA 24061e-mail: mwellis@vt.edu
D. A. Dillard
Department of Engineering Science and Mechanics,
Virginia Polytechnic Institute and State University
, Blacksburg, VA 24061e-mail: dillard@vt.edu
J. Fuel Cell Sci. Technol. Nov 2009, 6(4): 041010 (7 pages)
Published Online: August 14, 2009
Article history
Received:
June 16, 2007
Revised:
November 29, 2007
Published:
August 14, 2009
Citation
Sole, J. D., Ellis, M. W., and Dillard, D. A. (August 14, 2009). "Experimental and Analytical Study of Gas Diffusion Layer Materials for Ribbon Fuel Cells." ASME. J. Fuel Cell Sci. Technol. November 2009; 6(4): 041010. https://doi.org/10.1115/1.3006307
Download citation file:
Get Email Alerts
Cited By
State of Health Estimation Method for Lithium-Ion Batteries Based on Multifeature Fusion and BO-BiGRU Model
J. Electrochem. En. Conv. Stor (November 2025)
Nitrogen and Phosphorus Co-Doped Hard Carbon Materials as High-Performance Anode for Sodium Ion Batteries
J. Electrochem. En. Conv. Stor (August 2025)
In-situ synthesis nano PtRuW/WC HER catalyst for acid hydrogen evolution by microwave method
J. Electrochem. En. Conv. Stor
Related Articles
Multi-Resolution PEM Fuel Cell Model Validation and Accuracy Analysis
J. Fuel Cell Sci. Technol (February,2006)
Electrical Performance of PEM Fuel Cells With Different Gas Diffusion Layers
J. Fuel Cell Sci. Technol (August,2011)
Simplified Model to Predict Incipient Flooding/Dehydration in Proton Exchange Membrane Fuel Cells
J. Fuel Cell Sci. Technol (August,2007)
Numerical Modeling of Proton Exchange Membrane Fuel Cell With Considering Thermal and Relative Humidity Effects on the Cell Performance
J. Fuel Cell Sci. Technol (August,2006)
Related Proceedings Papers
Related Chapters
Experiment Study on the Current Density Distribution of PEMFC
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)
The Study on Linear Component Technique in Identifying the Polarization of Electromagnetic Waves
International Conference on Computer and Electrical Engineering 4th (ICCEE 2011)
Effects of Metallic Plate and Objects on Performance of Inverted F Antenna for ISM Band Application
International Conference on Computer and Automation Engineering, 4th (ICCAE 2012)