The mixing flows in microchannels were examined using numerical methods. To speed up fluid mixing, it is essential to generate lateral transport of mass. In this study, the mixing flow is disrupted by either placing grooves or block obstacles on the walls of the channels. Since the grooves or the blocks appear in a periodic configuration, the velocity is solved only in a section of the channel. With the repeating cycle of flow velocity field, the fluid concentration can be calculated throughout the entire length of the channel. Good agreement with experiments in the mixing performance justifies the present methodology. Two different channel configurations are under consideration: grooved channels and obstructed channels. The results reveal that with straight grooves, a well organized vortex flow is formed in the vertical plane along the groove, which leads to a helical flow in the channel. The mixing performance can be enhanced by having grooves on both the top and the bottom walls arranged in a staggered manner, by which the transversal velocity is largely increased. It is seen that the strength of the secondary flow and, thus, the mixing can be improved by suitably choosing geometric parameters of the groove, such as the depth, the width, and the oblique angle. It is also shown that the efficient mixing for the staggered herringbone type groove is due to the fluid stratification caused by the exchange of position of the resulted counter-rotating vortices. As for the obstructed channels, the flows are in essence two dimensional. Very strong transversal velocity can be produced by narrowing down the flow passage in the channel. However, the efficient mixing is obtained at the cost of large pressure head loss.
Skip Nav Destination
e-mail: yytsui@mail.nctu.edu.tw
Article navigation
July 2008
Research Papers
Evaluation of the Mixing Performance of the Micromixers With Grooved or Obstructed Channels
Yeng-Yung Tsui,
Yeng-Yung Tsui
Department of Mechanical Engineering,
e-mail: yytsui@mail.nctu.edu.tw
National Chiao Tung University
, Hsinchu 300, Taiwan R.O.C.
Search for other works by this author on:
Ching-Shiang Yang,
Ching-Shiang Yang
Department of Mechanical Engineering,
National Chiao Tung University
, Hsinchu 300, Taiwan R.O.C.
Search for other works by this author on:
Chung-Ming Hsieh
Chung-Ming Hsieh
Department of Mechanical Engineering,
National Chiao Tung University
, Hsinchu 300, Taiwan R.O.C.
Search for other works by this author on:
Yeng-Yung Tsui
Department of Mechanical Engineering,
National Chiao Tung University
, Hsinchu 300, Taiwan R.O.C.e-mail: yytsui@mail.nctu.edu.tw
Ching-Shiang Yang
Department of Mechanical Engineering,
National Chiao Tung University
, Hsinchu 300, Taiwan R.O.C.
Chung-Ming Hsieh
Department of Mechanical Engineering,
National Chiao Tung University
, Hsinchu 300, Taiwan R.O.C.J. Fluids Eng. Jul 2008, 130(7): 071102 (10 pages)
Published Online: June 25, 2008
Article history
Received:
May 17, 2007
Revised:
April 23, 2008
Published:
June 25, 2008
Citation
Tsui, Y., Yang, C., and Hsieh, C. (June 25, 2008). "Evaluation of the Mixing Performance of the Micromixers With Grooved or Obstructed Channels." ASME. J. Fluids Eng. July 2008; 130(7): 071102. https://doi.org/10.1115/1.2948364
Download citation file:
Get Email Alerts
Related Articles
Numerical Analysis of Wall Slip Effects on Flow of Newtonian and Non-Newtonian Fluids in Macro and Micro Contraction Channels
J. Fluids Eng (January,2007)
Analysis of Vortical Flow Field in a Propeller Fan by LDV Measurements and LES—Part I: Three-Dimensional Vortical Flow Structures
J. Fluids Eng (December,2001)
Level-Set Computations of Free Surface Rotational Flows
J. Fluids Eng (November,2005)
Effect of Surface Microstructure on Microchannel Heat Transfer Performance
J. Heat Transfer (December,2011)
Related Proceedings Papers
Related Chapters
Cavitating Structures at Inception in Turbulent Shear Flow
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Pulsating Supercavities: Occurrence and Behavior
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Vortex-Induced Vibration
Flow Induced Vibration of Power and Process Plant Components: A Practical Workbook