Stability and synchronous-response predictions, which were presented by Childs et al. (2014, “A Lateral Rotordynamics Primer on Electric Submersible Pumps (ESPs) for Deep Subsea Applications,” 43th International Pump Users Symposium, Texas A&M University, College Station, TX, pp. 1–18), are re-evaluated to include the effect of the fluid between the pump housing and well casing. Conclusions are made based on these new findings. The same two-line rotor–housing model is used to model the pump's rotor and its housing. The model dimensions are based on direct measurements of an ESP. The pump rotor and pump housing are only connected together at each stage by reaction forces and moments from seals and bushings. The rotor model is pinned to the housing at the rotor's ends. The housing model is pinned to ground at its ends. Synchronous response predictions are presented for: (1) relative rotor–housing motion and (2) housing velocity-response amplitudes. When handling viscosity of water, the rotor–housing model is predicted to be stable at new (centered) 1× clearances but rapidly becomes unstable with enlarged clearances (2× and 3×), primarily due to rapidly dropping rotor–housing natural frequencies. The impact of introducing effective swirl brakes for the stages' wear ring seals was investigated for a pump running at 3600 rpm. Their predicted impact on stability and synchronous response was: (1) Onset speeds of instabilities (OSIs) were elevated well above running speed and (2) synchronous response amplitudes were reduced modestly. Housing-response amplitudes varied considerably with the choice of housing-termination locations. For a pump rotor length of Lr, varying the lengths of a centered housing over 1.5 Lr, 2 Lr, and 3 Lr changes the housing's natural frequency. This natural frequency can coincide with the running speed with proper termination conditions. If the running speed and natural frequency coincide, large housing vibration amplitudes associated with resonance would exceed most vibration regulations; however, relative rotor–stator response amplitudes were a small fraction of clearances for all the cases. When handling emulsions at markedly higher viscosities, with a pump speed of 3600 rpm and new centered clearances, the predicted OSI was below 300 rpm. The OSI rapidly increased as the seals were displaced eccentrically, quickly elevating the first rotor–stator natural frequency above 1800 rpm and the OSI above 3600 rpm. With the model stabilized at 0.2 eccentricity, the synchronous relative rotor–housing amplitudes were a small fraction of seal clearances. Swirl brakes were not predicted to be effective in elevating pump OSIs for high viscosity fluids with new clearances; however, they became effective as clearances were increased. An ESP housing can contact the well casing in many possible scenarios (axial locations, contact-area length or girth, etc.). A midspan, point radial contact was examined and modeled as a stiff-spring connection from the housing to ground. For both water and oil–water emulsions, a stiff housing-to-casing contact produced major elliptical housing motion (versus circular motion without contact). However, it had a comparably minor impact on relative rotor–housing response amplitudes or rotordynamic stability.
Skip Nav Destination
Article navigation
June 2017
Research-Article
Including Housing–Casing Fluid in a Lateral Rotordynamics Analysis on Electric Submersible Pumps
Dara W. Childs,
Dara W. Childs
Leland T. Jordan Professor
Texas A&M Turbomachinery Laboratory,
College Station, TX 77843
e-mail: dchilds@tamu.edu
Texas A&M Turbomachinery Laboratory,
College Station, TX 77843
e-mail: dchilds@tamu.edu
Search for other works by this author on:
Stephen Phillips
Stephen Phillips
Search for other works by this author on:
Clay S. Norrbin
Dara W. Childs
Leland T. Jordan Professor
Texas A&M Turbomachinery Laboratory,
College Station, TX 77843
e-mail: dchilds@tamu.edu
Texas A&M Turbomachinery Laboratory,
College Station, TX 77843
e-mail: dchilds@tamu.edu
Stephen Phillips
Contributed by the Structures and Dynamics Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received August 29, 2016; final manuscript received September 2, 2016; published online February 1, 2017. Editor: David Wisler.
J. Eng. Gas Turbines Power. Jun 2017, 139(6): 062505 (12 pages)
Published Online: February 1, 2017
Article history
Received:
August 29, 2016
Revised:
September 2, 2016
Citation
Norrbin, C. S., Childs, D. W., and Phillips, S. (February 1, 2017). "Including Housing–Casing Fluid in a Lateral Rotordynamics Analysis on Electric Submersible Pumps." ASME. J. Eng. Gas Turbines Power. June 2017; 139(6): 062505. https://doi.org/10.1115/1.4035358
Download citation file:
Get Email Alerts
Cited By
Blade Excitation Alleviation of a Nozzleless Radial Turbine by Casing Treatment Based on Reduced Order Mode
J. Eng. Gas Turbines Power
Design And Testing of a Compact, Reverse Brayton Cycle, Air (R729) Cooling Machine
J. Eng. Gas Turbines Power
Experimental Study on Liquid Jet Trajectory in Cross Flow of Swirling Air at Elevated Pressure Condition
J. Eng. Gas Turbines Power
Related Articles
Lateral Equilibrium Position Analysis Program With Applications to Electric Submersible Pumps
J. Eng. Gas Turbines Power (June,2018)
Fiber-Surface Quality Enhancement to Improve the Performance Properties of Friction Materials
J. Tribol (September,2017)
Swirl Brake Effect on the Rotordynamic Stability of a Shrouded Impeller
J. Turbomach (January,1999)
Tribological Behaviors of Polymer-Based Hybrid Nanocomposite Brake Pad
J. Tribol (May,2018)
Related Proceedings Papers
Related Chapters
Contamination and Impacts of Exploration and Production Waste Constituents
Guidebook for Waste and Soil Remediation: For Nonhazardous Petroleum and Salt Contaminated Sites
Unbalance
Fundamentals of Rotating Machinery Diagnostics
Introduction I: Role of Engineering Science
Fundamentals of heat Engines: Reciprocating and Gas Turbine Internal Combustion Engines