In this paper, a dynamic model that considers the vibrations of both the workpiece and fixture elements in order to accurately predict the friction damping over a wide range of clamping forces has been developed. The model is established based on the theory of variational inequality and solved via a nonlinear FEM. It is shown that the model is capable of predicting the system dynamics over a wide range of clamping forces. It is also demonstrated that the increasing then decreasing trend of the damping ratio caused by “interface locking” is due to the relative velocity change at the contact interface. With multiple contact interfaces, the “locking” occurs sequentially. Finally, the model is used to study the influence of friction damping on machining process stability.
Skip Nav Destination
Article navigation
Technical Papers
Influence of Friction Damping on Workpiece-Fixture System Dynamics and Machining Stability
B. Fang,
B. Fang
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801
Search for other works by this author on:
R. E. DeVor,
R. E. DeVor
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801
Search for other works by this author on:
S. G. Kapoor
S. G. Kapoor
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801
Search for other works by this author on:
B. Fang
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801
R. E. DeVor
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801
S. G. Kapoor
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801
Contributed by the Manufacturing Engineering Division for publication in the JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING. Manuscript received February 2001. Revised August 2001. Associate Editor: S. Jack Hu.
J. Manuf. Sci. Eng. May 2002, 124(2): 226-233 (8 pages)
Published Online: April 29, 2002
Article history
Received:
February 1, 2001
Revised:
August 1, 2001
Online:
April 29, 2002
Citation
Fang , B., DeVor , R. E., and Kapoor, S. G. (April 29, 2002). "Influence of Friction Damping on Workpiece-Fixture System Dynamics and Machining Stability ." ASME. J. Manuf. Sci. Eng. May 2002; 124(2): 226–233. https://doi.org/10.1115/1.1459086
Download citation file:
Get Email Alerts
A Study on the Influence of Polypropylene Melt Flow Index on Nonwoven Fibers Produced Through Hot Melt Centrifugal Spinning
J. Manuf. Sci. Eng (April 2025)
Arc Characteristics of Aluminum Alloy Double-Wire High-Frequency Pulsed GMAW
J. Manuf. Sci. Eng (April 2025)
Related Articles
Vibration Suppression in Cutting Tools Using a Collocated Piezoelectric Sensor/Actuator With an Adaptive Control Algorithm
J. Vib. Acoust (October,2010)
3D FEA Modeling of Hard Turning
J. Manuf. Sci. Eng (May,2002)
Effect of Low-Frequency Modulation on Lubrication of Chip-Tool Interface in Machining
J. Tribol (January,2005)
An Elastodynamic Model of Frictional Contact and Its Influence on the Dynamics of a Workpiece-Fixture System
J. Manuf. Sci. Eng (August,2001)
Related Proceedings Papers
Related Chapters
Modeling of Cutting Force in Vibration-Assisted Machining
Vibration Assisted Machining: Theory, Modelling and Applications
Cutting and Machining
Fabrication of Metallic Pressure Vessels
Energy Consumption
Engineering Practice with Oilfield and Drilling Applications