A high-temperature pressurized air-based receiver is considered as a module for power generation via solar-driven gas turbines. A set of silicon carbide cavity-receivers attached to a compound parabolic concentrator (CPC) are tested on a solar tower at stagnation conditions for 35 kW solar radiative power input under mean solar concentration ratios of 2000 suns and nominal temperatures up to 1600 K. A heat transfer model coupling radiation, conduction, and convection is formulated by Monte Carlo ray-tracing, finite volume, and finite element techniques, and validated in terms of experimentally measured temperatures. The model is applied to elucidate the effect of material properties, geometry, and reflective coatings on the cavity’s thermal and structural performances.
Skip Nav Destination
e-mail: aldo.steinfeld@eth.ch
Article navigation
February 2012
Research Papers
A Modular Ceramic Cavity-Receiver for High-Temperature High-Concentration Solar Applications
I. Hischier,
I. Hischier
Department of Mechanical and Process Engineering
, ETH Zürich, 8092 Zürich, Switzerland
Search for other works by this author on:
P. Poživil,
P. Poživil
Department of Mechanical and Process Engineering
, ETH Zürich, 8092 Zürich, Switzerland
Search for other works by this author on:
A. Steinfeld
e-mail: aldo.steinfeld@eth.ch
A. Steinfeld
Department of Mechanical and Process Engineering
, ETH Zürich, 8092 Zürich, Switzerland
; Solar Technology Laboratory, Paul Scherrer Institute
, 5232 Villigen, Switzerland
Search for other works by this author on:
I. Hischier
Department of Mechanical and Process Engineering
, ETH Zürich, 8092 Zürich, Switzerland
P. Poživil
Department of Mechanical and Process Engineering
, ETH Zürich, 8092 Zürich, Switzerland
A. Steinfeld
Department of Mechanical and Process Engineering
, ETH Zürich, 8092 Zürich, Switzerland
; Solar Technology Laboratory, Paul Scherrer Institute
, 5232 Villigen, Switzerland
e-mail: aldo.steinfeld@eth.ch
J. Sol. Energy Eng. Feb 2012, 134(1): 011004 (6 pages)
Published Online: November 1, 2011
Article history
Received:
May 23, 2011
Revised:
September 8, 2011
Online:
November 1, 2011
Published:
November 1, 2011
Citation
Hischier, I., Poživil, P., and Steinfeld, A. (November 1, 2011). "A Modular Ceramic Cavity-Receiver for High-Temperature High-Concentration Solar Applications." ASME. J. Sol. Energy Eng. February 2012; 134(1): 011004. https://doi.org/10.1115/1.4005107
Download citation file:
Get Email Alerts
Mass Flow Control Strategy for Maximum Energy Extraction in Thermal Energy Storage Tanks
J. Sol. Energy Eng (December 2025)
Exergy Optimization of a Hybrid Multi-Evaporative Desalination Plant Powered by Solar and Geothermal Energy
J. Sol. Energy Eng (June 2025)
Correlation for Maximum Heat Transfer Between Fluidized Bed and Its Wall and Application to Solar Power Plants
J. Sol. Energy Eng (June 2025)
Related Articles
Monte Carlo Radiative Transfer Modeling of a Solar Chemical Reactor for The Co-Production of Zinc and Syngas
J. Sol. Energy Eng (February,2005)
Heat Transfer Analysis of a Novel Pressurized Air Receiver for Concentrated Solar Power via Combined Cycles
J. Thermal Sci. Eng. Appl (December,2009)
An Improved Computational Procedure for Sub-Micron Heat Conduction
J. Heat Transfer (October,2003)
On the Thermal Performance Characteristics of Three-Dimensional Multichip Modules
J. Electron. Packag (September,2004)
Related Chapters
Radiation
Thermal Management of Microelectronic Equipment
Radiation
Thermal Management of Microelectronic Equipment, Second Edition
Energy Balance for a Swimming Pool
Electromagnetic Waves and Heat Transfer: Sensitivites to Governing Variables in Everyday Life