This paper presents an investigation of a range of engine realistic rim seals starting from a simple axial seal to different types of overlapping seals. The experiments were performed in a large-scale linear cascade equipped with a secondary air system capable of varying independently both the mass fraction as well as the swirl velocity of the leakage air. The experimental results were also complemented by computationally fluid dynamics (CFD) to provide better insight in the flow physics. It has been found that the key feature of the rim seals that affect their impact on overall loss generation and their ability to provide good sealing effectiveness was the location and the size of the recirculation zones within the rim seal. The requirements for good sealing and reduced spoiling effects on the main gaspath flow often led to contradictory designs. In general, the recirculation zones were found to improve sealing by reducing the effect of the pitchwise (circumferential) variation in the pressure distribution due to the blade's potential field, and thus reduce ingestion. However, at the same time the recirculation zones tend to increase the loss generation. The best compromise was found when the outer part of the seal and its interface with the rotor platform was as smooth as possible to minimize the spoiling losses, while the recirculation zones were confined to the inner part of the seal to maintain acceptable levels of sealing effectiveness. A new rim seal design, which utilizes the best attributes of the above mentioned designs was developed. Linear cascade tests showed the losses due to the leakage-mainstream interaction were reduced by 33% compared to the datum seal design. Further validation was performed by examining the new configuration using unsteady full-stage calculations under engine realistic conditions. These calculations suggest an improvement of nearly 0.2% in the stage efficiency.

References

1.
McLean
,
C.
,
Camci
,
C.
, and
Glezer
,
B.
,
2001
, “
Mainstream Aerodynamic Effects Due to Wheelspace Coolant Injection in a High-Pressure Turbine Stage: Part I—Aerodynamic Measurements in the Stationary Frame
,”
ASME J. Turbomach.
,
123
(4), pp. 687–696.10.1115/1.1401026
2.
Hunter
,
S. D.
, and
Manwaring
,
S. R.
,
2000
, “
Endwall Cavity Flow Effects on Gaspath Aerodynamics in an Axial Flow Turbine: Part I—Experimental and Numerical Investigation
,” ASME Paper No. 2000-GT-651.
3.
Rehder
,
H. J.
, and
Dannhauer
,
A.
,
2006
, “
Experimental Investigation of Turbine Leakage Flows on the 3D Flow Field and Endwall Heat Transfer
,”
ASME
Paper No. GT2006-90173.10.1115/GT2006-90173
4.
Schuler
,
P.
,
Dullenkopf
,
K.
, and
Bauer
,
H.
, 2011, “
Investigation of the Influence of Different Rim Seal Geometries in a Low-Pressure Turbine
,”
ASME
Paper No. GT2011-45682.10.1115/GT2011-45682
5.
Biesinger
,
T. E.
, and
Gregory-Smith
,
D.
,
1993
, “
Reduction in Secondary Flows and Losses in a Turbine Cascade by Upstream Boundary Layer Blowing
,” ASME Paper No. 93-GT-114.
6.
Marini
,
R.
, and
Girgis
,
S.
,
2007
, “
The Effect of Blade Leading Edge Platform Shape on Upstream Disc Cavity to Mainstream Flow Interaction of a High-Pressure Turbine Stage
,”
ASME
Paper No. GT2007-27429.10.1115/GT2007-27429
7.
de la Rosa Blanco
,
E.
,
Hodson
,
H. P.
, and
Vazques
,
R.
,
2006
, “
Effect of the Leakage Flows and the Upstream Platform Geometry on the Endwall Flows of a Turbine Cascade
,”
ASME
Paper No. GT2006-90767.10.1115/GT2006-90767
8.
Mirzamoghadam
,
A. V.
,
Heitland
,
G.
,
Morris
,
M. C.
,
Smoke
,
J.
,
Malak
,
M.
, and
Howe
,
J.
, 2008, “
3D CFD Ingestion Evaluation of a High Pressure Turbine Rim Seal Disk Cavity
,”
ASME
Paper No. GT2008-50531.10.1115/GT2008-50531
9.
Lott
,
P.
,
Hills
,
N. J.
,
Chew
,
J.W.
, and
Scanlon
,
T.
,
2009
, “
High Pressure Turbine Stage Endwall Profile Optimisation for Performance and Rim Seal Effectiveness
,”
ASME
Paper No. GT2009-59923.10.1115/GT2009-59923
10.
Schuepbach
,
P.
,
Abhari
,
R. S.
,
Rose
,
M. G.
, and
Gier
,
J.
,
2009
, “
Influence of Rim Seal Purge Flow on Performance of an Endwall-Profiled Axial Turbine
,”
ASME
Paper No. GT2009-59653.10.1115/GT2009-59653
11.
Popovíc
,
I.
, and
Hodson
,
H. P.
,
2010
, “
Aerothermal Impact of the Interaction Between Hub Leakage and Mainstream Flows In Highly-Loaded HP Turbine Blades
,”
ASME
Paper No. GT2010-22311.10.1115/GT2010-22311
12.
Lynch
,
S. P.
, and
Thole
,
K. A.
, 2007, “
The Effect of Combustor-Turbine Interface Gap Leakage on the Endwall Heat Transfer for a Nozzle Guide Vane
,”
ASME
Paper No. GT2007-27867.10.1115/GT2007-27867
13.
Dannhauer
,
A.
,
2008
, “
Analysis of Cooling Effectiveness and Heat Transfer Variations on the Endwall of a Nozzle Guide Vane Caused by Turbine Leakage Flows
,”
ASME
Paper No. GT2008-50555.10.1115/GT2008-50555
14.
Wright
,
L. M.
,
Gao
,
Z.
,
Yang
,
H.
, and
Han
,
J. C.
,
2006
, “
Film Cooling Effectiveness Distribution on a Gas Turbine Blade Platform With Inclined Slot Leakage and Discrete Film Hole Flows
,”
ASME
Paper No. GT2006-90375.10.1115/GT2006-90375
15.
Amecke
,
J.
,
1967
, “
Auswertung von Nachlaufmessungen an ebenen Schaufelgittern
,”
Bericht 67A
49
, pp. 1–23.
16.
Popovíc
,
I.
, and
Hodson
,
H. P.
,
2012
, “
The Effects of a Parametric Variation of the Rim Seal Geometry on the Interaction Between Hub Leakage and Mainstream Flows in HP Turbines
,” ASME Paper No. GT2012-68025.
17.
Feiereisen
,
J. M.
,
Paolillo
,
R. E.
, and
Wagner
,
J.
, “
Turbine Rim Seal Ingestion and Platform Cooling Experiments
,
AIAA
Paper No. 2000-3371.10.2514/6.2000-3371
18.
Popovíc
,
I.
,
Hodson
,
H. P.
,
Wolf
,
T.
, and
Janke
,
E.
,
2011
, “
The Effects of Unsteadiness and Compressibility on the Interaction Between Hub Leakage and Mainstream Flows in HP Turbines
,”
ASME
Paper No. GT2011-46608.10.1115/GT2011-46608
You do not currently have access to this content.